思科路由器大家也習慣叫為Linksys路由器，是國內使用者使用很多的路由器品牌。下面是小編整理的關於思科路由器英文版設定，歡迎大家參考!
思科路由器進入管理介面方法：
1、先檢視IP，方法：win+r---輸入:cmd---在再黑白介面輸入：ipconfig，按回車
2、根據閘道器檢視路由器地址。若閘道器與路由器的ip一般是相同的
3、在IE位址列中輸入地址：
4、彈出路由器登陸介面輸入路由器的預設登陸使用者名稱：admin 密碼：admin(如果不正確，就看路由器背面)。
思科路由器中英文翻譯
System summary(系統總結)
The System Summary screen displays the router's current status and settings. This information is read only. If you click the button with underline, it will hyperlink to related setup pages. On the right side of the screen and all other screens in the Utility will be a link to the Site Map, which has links to all of the Utility's tabs.
Serial Number: The serial number of the RV082 unit.
System up time: The length of time in Days, Hours, and Minutes that the RV082 is active.
Firmware version: The current version number of the firmware installed on this unit.
CPU: The type of the RV082 processor. It is Intel IXP425.
DRAM: The size of DRAM on the board. It is 32MB.
Flash: The size of Flash on the board. It is 16MB.
Configuration: If you need guideline to re-configure the router, you may launch Wizard.
Port Statistics: Users can click the port number from port diagram to see the status of the selected port
該系統總的螢幕顯示路由器的當前狀態和設定。此資訊是隻讀的。如果您按一下按鈕，與強調，將相關的設定超連結的網頁。論螢幕和實用工具的所有其他螢幕右側將是一個網站地圖，它的效用的標籤各個環節的聯絡。
編號：該RV082單位的序列號。
系統時間：在幾天，幾小時的時間長度，及記錄的RV082處於活動狀態。
韌體版本：對本單位安裝的韌體的版本號。
處理器：RV082的處理器型別。這是英特爾IXP425。
記憶體：記憶體上的電路板尺寸。這是32MB。
快訊：在快閃記憶體上的電路板尺寸。這是16MB的。
配置：如果您需要的指引，重新配置路由器，您可能會啟動向導。
港口統計：使用者可以從港口圖單擊埠編號，以檢視選定的埠的狀態
setup(設定)
The Setup screen contains all of the router's basic setup functions. The device can be used in most network settings without changing any of the default values. Some users may need to enter additional information in order to connect to the Internet through an ISP (Internet Service Provider) or broadband (DSL, cable modem) carrier.
Host Name & Domain Name:
Enter a host and domain name for the Router. Some ISPs (Internet Service Providers) may require these names as identification, and these settings can be obtained from your ISP. In most cases, leaving these fields blank will work.
LAN Setting:
This is the Router's LAN IP Address and Subnet Mask. The default value is for IP address and for the Subnet Mask.
安裝螢幕包含路由器的基本設定的所有功能。該器件可用於在大多數網路設定，在不改變預設的任何值。有些使用者可能需要輸入更多的資訊，以便連線到網際網路，通過一個ISP(網際網路服務提供商)或寬頻(DSL，電纜調變解調器)承運人。
主機名和域名：
輸入一個路由器的主機和域名。有些ISP(網際網路服務提供商)可能需要這些名稱作為識別，這些設定可以從ISP獲得的。在大多數情況下，這些領域留下空白的工作。
區域網設定：
這是路由器的區域網IP地址和子網掩碼。預設值是IP地址和子網掩碼
DHCP(動態主機配置協議)
The Router can be used as a DHCP (Dynamic Host Configuration Protocol) server on your network. A DHCP server assigns available IP addresses to each computer on your network automatically
該路由器可以作為DHCP(動態主機配置協議)您的網路伺服器上。一個DHCP伺服器分配網路上可用的IP地址給每臺電腦自動
System management(系統管理)
There are two functions provided for users - Smart Link Backup and Load Balance. If users select DMZ in setup page, users could not do the Dual WAN setting here.
If Load Balance (Auto Mode) is selected, it will be automatically computing the max bandwidth of WAN1 and WAN2 by using Weighted Round Robin to balance the loading.
Network Service Detection
This tool can detect the network connection status of ISP by pinging Default Gateway, ISP Host, Remote Host or DNS Lookup Host.
Retry count: The count of ping. The default is 5.
Retry timeout: The interval between two ping actions. The default is 30 seconds.
When Fail:
Generate the Error Condition in the System Log: The Router will generate the System Log when ping fail to inform users that the ISP connection is disconnected.
Remove the Connection: This WAN Interface will be suspended when the network connection to ISP is not active. The traffic on this WAN will be dispatched to the other WAN port. Once ISP returns to c
有兩個功能，為使用者提供-智慧鏈路備份和負載平衡。如果使用者選擇非軍事區的設定頁，使用者不能這樣做的雙WAN設定在這裡。
如果負載平衡(自動模式)的選擇，它會自動計算採用加權迴圈，以平衡負載的WAN1和WAN2最大頻寬。
網路服務檢測
此工具可以檢測到通過Ping預設閘道器，ISP的主機，遠端主機或DNS查詢主機的ISP網路的連線狀態。
重試計數：在平罪名。預設值為5。
重試超時：兩平的行動間隔。預設為30秒。
當失敗：
生成系統日誌中的錯誤條件：路由器將生成系統日誌時，平沒有通知的ISP連線的使用者斷開。
刪除連線：廣域網介面，這將暫停使用時，網路連線到ISP並不活躍。關於這個廣域網流量將被派往其他廣域網埠。一旦返回到c的ISP
port management (埠管理)
In this router, users can configure the connection status for each port, such as Priority, Speed, Duplex, Auto-Negotiation and VLAN.
Basic Per Port Config.
Port ID: They are port 1~8, DMZ/Internet and Internet.
Interface: They are LAN, WAN2 or DMZ, WAN1.
Disable: Check the box, the port will be disabled. It is a per-port setting.
Priority: Select High or Normal for Port-based QoS (Quality of Service). QoS is used to maximize a network’s performance and this setting allows you to prioritize performance on eight LAN ports.
Speed: Users can manually config the per-port speed as 10Mbps or 100Mbps.
Duplex: Users can manually config the per-port duplex as half-duplex or full-duplex.
Auto-negotiation: Users can configure the per-port mode as Auto-negotiation, so Users will not need to setup speed and duplex.
VLAN (Virtual LAN): A VLAN Group is a broadcast domain, and the stations on the same VLAN group can communicate with each other, and the stations on the separate VLAN groups
在這種路由器，使用者可以為每個如優先，速度，雙工，自動協商和VLAN埠，配置的連線狀態。
每埠的基本配置。
埠ID：他們是埠1〜8，非軍事區/網際網路和網際網路。
介面：他們是區域網，WAN2或DMZ，WAN1。
禁用：檢查中，該埠將被禁用。這是一個每個埠設定。
優先順序：選擇高或普通的基於埠的QoS(服務質量)。服務質量是用來最大限度地提高網路的效能和此設定允許您在八個優先LAN埠的效能。
速度：使用者可以手動配置每個埠為10Mbps或100Mbps的`速度。
複式：使用者可以手動配置的每一半埠全雙工半雙工或全雙工。
自動談判：使用者可以配置每個埠的模式，自動協商，讓使用者將不需要安裝的速度和雙工。
VLAN(虛擬區域網)：一個VLAN集團是一個廣播域，並在同一VLAN組的車站可以相互溝通，並在不同的VLAN組的車站
firewall (防火牆)
From the Firewall Tab, you can configure the Router to deny or allow specific internal users from accessing the Internet. You can also configure the Router to deny or allow specific Internet users from accessing the internal servers. You can set up different packet filters for different users that are located on internal (LAN) side or external (WAN) side based on their IP addresses or their network Port number.
Firewall
The default is enabled. If users disable the Firewall function, SPI, DoS, Block WAN Request will be disabled, Remote Management will be enabled and Access Rules and Content Filter will be disabled.
Stateful Packet Inspection (SPI)
The Router's Firewall uses Stateful Packet Inspection to maintain connection information that passes through the firewall. It will inspect all packets based on the established connection, prior to passing the packets for processing through a higher protocol layer.
Denial of Service (DoS)
Protect internal networks from Internet att
從防火牆選項卡，您可以配置路由器，拒絕或允許從網際網路訪問特定內部使用者。您還可以配置路由器拒絕或允許訪問內部伺服器的特定網際網路使用者。您可以設定該位於內部(LAN)一方或外部(廣域網)方根據其IP地址或埠號的網路不同使用者的不同資料包篩選器。
防火牆
預設被啟用。如果使用者禁用防火牆功能，SPI和拒絕服務，座廣域要求將被停用，遠端管理將啟用和訪問規則和內容過濾器將被禁用。
狀態包檢測(SPI)
路由器的防火牆使用狀態包檢測技術來保持連線資訊穿過防火牆。它將考察了已建立的連線的所有資料包，通過前處理的資料包通過一個更高的協議層。
對拒絕服務(DoS)
從網際網路先進交通運輸保護內部網路
Protectlink(防護連線)
Trend Micro™ ProtectLink Gateway is a hosted security service that stops spam and filters URLs
to prevent unwanted content from passing through your Linksys router. ProtectLink stops over 97%
of spam and controls access to Web sites based on the categories you select.
More...
I want to buy Trend Micro ProtectLink Gateway
I have purchased ProtectLink Gateway and want to register it
I have my Activation Code (AC) and want to activate ProtectLink Gateway
趨勢科技™ProtectLink閘道器是一項託管安全服務，停止垃圾郵件和過濾器的網址
防止通過Linksys路由器通過不想要的內容。 ProtectLink停止超過97%
垃圾郵件和控制獲取有關您選擇的類別為基礎的網站。
更多...
我想購買趨勢科技ProtectLink閘道器
我已經購買ProtectLink閘道器，並希望將其註冊
我有我的啟用程式碼(AC)和要啟用ProtectLink閘道器
VPN(虛擬專用網路) log(原本) wizard(嚮導)
Support (支援) Logout (關閉)
